广州正菱|三菱
当前位置:首页 >> 资料下载 >> 三菱 >> AJ系列CC-Link模块
1、三菱 C6C64C64T 三菱 C6C64C64T 连接维护说明书
Correctly connect the output side (terminal U, V, W). The servomotor will not run properly if incorrectly connected. Always install an AC reactor per each power supply unit. Alw
2、三菱 C70系列 三菱 C70系列,编程说明书(M系)
(1) 执行主轴同期时,必须同时对基准主轴和同期主轴发出旋转指令。但是,同期主轴的旋转方向与正反转指 令无关,而是取决于基准主轴的旋转方向和主轴同期旋转方向。 (2) 在主轴转速指令为ON的状态下,接通主轴同期控制信号,虽然会进入主轴同期控制模式,但是不会进行 实际的同期控制。向基准主轴发出转速指令之后才会进行同期控制,输出主轴同期完成信号。 (3) 主轴同期控制下正
3、三菱 C70系列 三菱 C70系列 规格说明书 -英
The items that are not described in this manual must be interpreted as "not possible". This manual is written on the assumption that all option functions are added. Some fu
4、三菱 C70系列 三菱 C70系列 规格说明书
This is the value that is used by rotary tools. As the tool length offset amount, among the offset amounts for the position of the tool moving in the direction parallel to the control axis,
5、三菱 C70系列 三菱 C70系列 连接说明书(英)
Do not open/close the front cover while the power is ON or during operation. The high voltage terminals and charged sections will be exposed, and this could result in electric shocks. Do not r
6、三菱 C70系列 三菱 C70系列 连接说明书
-- 跳跃信号接口规格 --- 输入接通电压:18V以上25.2V以下 输入接通电流:6mA以上 输入关闭电压:4V以下 输入关闭电流:2mA以下 输入信号保持时间 (Ton):2ms以上 内部相应时间:0.08ms以下 (注1)NC 将 2ms以上的输入信号识别为有效的跳跃信号。如果使用机床触点(继电器 等) ,可能会因振动而导致误动作,因此请使用半导体触点
7、三菱 C70系列 三菱 C70系列 设定说明书(英)
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and/or reused. This symbol means that batteries and accumulators,
8、三菱 C70系列 三菱 C70系列 设定说明书
位置检测系统具有在每次打开 CNC 电源时,记忆决定参考点的(原点) “相对位置检测” ,与记忆关闭 CNC 电源期间 的位置,打开CNC电源后,不再决定参考点(原点)而直接运行的“对位置检测” 。 “相对位置检测” “对位置检测”各自参考点的决定方法有“挡块式方式(挡块式参考点返回) ”与“无挡块方式(无 挡块式参考点返回) ” 。 (注) 即使是“
9、三菱 C70系列 三菱 C70系列 使用说明书(英)
If the BATTERY LOW warning is output, save the machining programs, tool data and parameters to an input/output device, and then replace the battery. If the BATTERY alarm occurs, the machini
10、三菱 CC-Link 三菱 CC-Link IE控制器网络参考手册
此功能是指,网络的各站将数据写入到链接软元件 (LB/LW) 的本站发送范围中,并将其发 送至同一网络中的所有站。 链接继电器 (LB)和链接寄存器 (LW)可分别发送 /接收 ON/OFF信息和 16 位数据。 (1) 设置 LB/LW 的各站发送范围 通过管理站的 [Network range assignment(网络范围分配 )]-[LB/LW settings(
11、三菱 CC-link 三菱 CC-link safety系统远程IO模块用户手册(详细篇)
• 应防止安全远程I/O模块摔落或受到强烈撞击。 • 不要将安全远程I/O模块的印刷电路板从外壳上拆下。 否则可能导致故障。 • 应注意安全远程I/O模块内不要弄进切屑和布线碎块等异物。 否则会引起火灾、故障、误动作。 • 将安全远程 I/O模块安装到控制盘等中时,为了保持通风良好,或者易于更换模 块,模块的上下部位与
12、三菱 CC-link 三菱 CC-link ,safety系统主站模块用户手册
a: 安全远程 I/O站的响应延迟导致的延迟时间 b: 从安全远程I/O站发送至安全主站模块的延迟时间 c: 安全主站模块接收之后存储到缓冲存储器中的延迟时间 d:将安全主站模块的信息刷新到安全CPU模块中的延迟时间 e:顺控程序处理的执行时间 f:从安全主站模块发送到安全远程I/O站的延迟时间 g:安全远程 I/O站的内部处理导致的延迟时间 h:安全远程 I/O站的响
145条 每页12条 共13页 页码: 上一页 1 2 3 4 5 6 7 8 9 10 下一页 [尾页]