Warranty
Mitsubishi will not be held liable for damage caused by factors found not to
cause of Mitsubishi; machine damage or lost profits caused by faults in the Mit
products; damage, secondary damage, accident compensation caused by
factors unpredictable by Mitsubishi; damages to products other than Mit
products; and to other duties.
For safe use
• This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric
aerospace, medicine or passenger movement vehicles, consult with Mitsubis
• This product has been manufactured under strict quality control. However wh
installing the product where major accidents or losses could occur if the prod
This manual confers no industrial property rights or any rights of any other kin
does it confer any patent licenses. Mitsubishi Electric Corporation cannot b
responsible for any problems involving industrial property rights which may oc
a result of using the contents noted in this manual.
ment pressurized above the
ound the altitude of 0 m. If the
il.
n outside the control panel as
ng temperature, the ambient
y to which the equipment is
ation
shall not be considered.
shall not be considered.
esent
Number of times of
sweep
mplitude
10 times in each of
X, Y and Z directions
(for 80 min)
mm
−
sent
mplitude
mm
−
Y and Z directions
nt.
5.2 Output specifications
5.3 Performance specifications
Item Specification
Output method
Transistor output
(using module power supply in common) (sink)
Number of outputs 2 points
Isolation method Isolation with photocoupler
Rated load voltage 24V DC
Operating load voltage
range
Same as module power supply
Max. load current 0.1A/point 0.2 A/1 common
Max. inrush current 0.4A/10 ms
Leakage current at OFF 0.1mA or less/30V DC
Max. voltage drop at ON 1V or less (max.)/0.1A
Response
time
OFF→ON 1.0ms or less
ON→OFF 1.0ms or less
Surge suppression Zener diode
Common wiring method 2 point/1 common (1 point)
Internal protection for
outputs
Internal protection circuit none
Please connect the fuse in the connected load
outside.
Item Specification
Module
power
supply
Vol tage
20.4 to 28.8V DC (24V DC -15% to +20%)
Ripple ratio: Within 5%
Current
consumption
40mA (when all points are ON)
Initial current 70mA
Max. allowable
momentary power
failure period
PS1:1ms
Number of stations
occupied
4-, 8- or 16-point mode: 1 station
Noise durability
500Vp-p
Noise width: 1µs Cycle: 25 to 60 Hz
(by noise simulator)
Withstand voltage 500V AC for 1 min
Isolation resistance
10 MΩ or more between primary area (external
DC terminal) and secondary area (internal circuit)
by 500V DC megger
Protection class IP2X
I/O part connection method Connection with cable
6. Outside Dimensions
24G Y0 Y1 +24V
Unit: mm(inches)
20(0.79")
65(2.56") 500(19.69")
12(0.48")
500(19.69")
接头套件 MR-ECN1
伺服电机电源用电缆 MR-PWS2CBL03M-A2-L
DC 输入/晶体管输出模块 AJ65VBTCE32-32DT
运动CPU单元 A73CPUP21-S1
RS-485适配器 FX2NC-485ADP
小型CPU扩展电缆 GT15-A1SC07B
QCPU（Q模式）用总线连接电缆 GT15-QC06B
RS-422电缆 GT01-C100R4-25P
编码器接头 MR-J3ENSCBL20M-L
伺服电机 HC-MFS73B
伺服电机 HC-SFS102
SSCNET Ⅲ 接头套件 MR-J3BCN1
GOT到GOT连接电缆 GT15-C50BS
模块 AJ35PP-CNV-GI
变频器 FR-F740-15K-CHT
伺服电机 HC-SFS702B
性能型QCPU Q02CPU
RS-422电缆 FX-422CAB0
伺服电机 HC-KFS73K
输出模块 AY13C
温度控制模块 FX2N-2LC
CPU单元 A2USHCPU-S1
编码器电缆 MR-ENCBL20M-H
CPU单元 Q2ACPU
扩展电缆 A1SC60B
伺服电机电源用电缆 MR-PWS1CBL5M-A2-H
制动器接头 MR-BKCN
编码器接头 MR-J3ENSCBL30M-L
伺服电机 HC-MFS43B
连接电缆 FX-232CAB-2